XM0-J6

Compact controller XM0 for TVE and TVE-Q

Bus interface Modbus RTU

X-AIR-ZMAS

X-AIRCONTROL Modbus zone module

Room control

RJ12 socket

Control component for type TVE

VAV control unit variant TVE-Q-P1 (powder-coated)

Control component for type TVE

XM0-J6

CONTROL COMPONENT WITH DYNAMIC TRANSDUCER AND MODBUS RTU INTERFACE FOR X-AIRCONTROL

Compact device for VAV terminal unit TVE and TVE-Q

Controller, dynamic differential pressure transducer and actuator in one casing
Use in ventilation and air conditioning systems, only with clean air
Simple RJ12 connection socket for supply voltage and network
Compatible with the X-AIRCONTROL zone module Modbus
Volume flow rates qvmin and qvmax are pre-set in the factory and saved in the controller as variable parameters
High data transparency via standardised bus communication Modbus RTU, RS485
Setpoint value settings, override controls, parameter adjustment via Modbus register
Integrated display for volume flow rate display, operating status display and setting of operating parameters
Service access for manual adjustment devices and PC configuration software

General information

Application

All-in-one control devices for VAV terminal units types TVE and TVE-Q
Dynamic differential pressure transducer, electronic controller and actuator are combined in one casing
For clean air in ventilation and air conditioning systems
The standard filtration enables use in the supply air without additional dust protection measures
Application examples: Offices and classrooms
In the event of a strong occurrence of dust, install appropriate extract air filters upstream, as a partial volume flow is routed through the transducer for volume flow rate measurement.
If the air is heavily contaminated with dust, fluff, or sticky and moist components, an attachment with a static differential pressure transducer must be used, e.g. XS0-J6
Application examples: Extract air from changing areas and showers, hospital bedrooms
Various control options based on setpoint value default setting
Suitable for X-AIRCONTROL room control, Modbus zone module
Control circuits for e.g. temperature, humidity, and air quality control the variable volume flow by specifying setpoint values via the communication interface
Simple connection for supply voltage and network with one shared RJ12 terminal socket
Override control for activating qvmin, qvmax, shut-off, OPEN position, possible via the Modbus register
The actual volume flow rate value is available as a network data point
The damper blade position is available as a network data point

Control strategy

The volume flow controller works independently of the duct pressure
Differential pressure fluctuations do not result in permanent volume flow rate changes
To prevent the control from becoming unstable, a dead zone (hysteresis) is maintained, in which the damper blade is not moved
The flow rate range for the controller is set in the factory (qvmin: minimum volume flow rate, qvmax: maximum volume flow rate)
Operating parameters are defined by the order code and parameterised at the factory

Operating modes

Modbus (M): setpoint value specification via X-AIRCONTROL

Communication interface

Modbus RTU, RS 485
Data point list see Modbus register list

Parts and characteristics

Transducer based on dynamic measuring principle. It can only be used with clean air, as a partial volume flow is passed through the transducer
Overload-proof actuator
RJ12 connection socket with cover
Display and control elements for easy menu navigation
Menu navigation allows for adjusting operating parameters and communication interface
Service interface

Construction

TR0VM-024T-05I-DD15-MB with RJ12 connection socket
Can only be used for type TVE and TVE-Q

Commissioning

As the volume flow rates are factory-set, the control units have to be installed at the specified locations only
Network integration requires commissioning steps
Operating parameters can be adjusted on site (using the display, an adjustment device, or the Modbus register)

Useful additions

Adjustment device type GUIV3-M (order code AT-VAV-G3)
Room control X-AIRCONTROL with zone module Modbus type X-AIR-ZMO-MOD

Information technique

Function, Specification text, Order code

1 Differential pressure transducer
2 Actuator
3 Volume flow controller
4 Setpoint value via BACnet, Modbus or analogue signal
5 Shaft with effective pressure channel

Air terminal units control the volume flow in a closed loop, which means: measurement – comparison – adjustment.
The volume flow rate is obtained by measuring a differential pressure. This is effected via a differential pressure sensor. The integrated differential pressure transducer converts the differential pressure into a voltage signal. The actual volume flow value is available as a data point. Du to the factory adjustment, 100% always equals the nominal volume flow rate (q_vNom).
The volume flow setpoint value is specified by a higher-level controller (e.g. room temperature controller, air quality controller, central BMS). Variable volume flow control can be set between_vmin and q_vmax. It is possible to override the room temperature control by forced switching, e.g. for a shut-off
The controller compares the volume flow setpoint with the current actual value and adjusts the internal actuator according to the control deviation.

Category

Compact controller for volume flow rate
Control of a constant or variable volume flow rate setpoint
Electronic controller for connecting a reference variable and recording an actual value for integration into X-AIRCONTROL
The actual value relates to the nominal volume flow rate so that commissioning and subsequent adjustment are simplified

Application

Dynamic transmitter for clean air in ventilation and air conditioning systems

Supply voltage

24 V AC/DC

Actuator

Integral; slow-running (running time 100 s for 90°)

Installation orientation

Not critical

Interface/signalling

Modbus RTU (RS-485)

Connection

RJ12 connection socket for easy connection to X-AIRCONTROL, with rubber cap cover
Suitable for X-AIRCONTROL zone module X-AIR-ZMO-MOD

Interface information

Modbus: includes writing and reading of volumetric flow setpoint and actual value signal, damper position, override control

Special functions

Clearly visible external indicator light for indicating the functions: Set, not set, and power failure
Display for actual values, parameter setting and for test functions
Activation q_vmin, q_vmax, closed, open by X-AIRCONTROL

Parameter setting

Specific parameters for VAV terminal unit are factory-set
Operating values: q_vmin, q_vmax are factory-set
Subsequent adjustment via display and operating element directly on the unit or with optional tools: Setting device, PC software (each wired), in Modbus mode also via Modbus register access

Factory condition

Electronic controller factory-mounted on the terminal unit
Factory set parameters
Functional test under air; certified with sticker

TVE

–

D – P1

–

100

XM0-J6

20 – 350 [m³/h]

| |

2 3

1 Type
TVE VAV terminal unit

2 Acoustic cladding
No entry: without acoustic cladding
D with acoustic cladding

3 Material
No entry: Galvanised sheet steel
P1 Surface powder-coated, RAL 7001 (silver grey)
A2 Stainless steel construction

4 Air duct connection
No entry: Push-fit end, suitable for air ducts according to EN
1506; with groove for optional seal
FL Flanges on both ends

5 Nominal size [mm]
100, 125, 160, 200, 250, 315, 400

6 Accessories

No entry: without accessories
D2 Double lip seal both ends (only for push-fit end with groove)
G2 Matching flange for every flange (only with FL)

7 Attachment (control component)
XM0-J6 Volume flow controller with dynamic transducer, display,
Modbus RTU interface, RJ12 socket (for X-AIRCONTROL)

8 Operating mode
M Modbus RTU interface, variable operation (default setpoint value via Modbus register)

10 Operating values for factory setting
Volume flow rate [m³/h or l/s]
qᵥmin – qᵥmax

Order example: TVE/100/D2/XM0-J6/M/20-350 m³/h

Acoustic cladding	without
Material	galvanised sheet steel
Nominal size	100 mm
Accessories	Double lip seal both ends
Attachment (control components)	Compact controller volume flow, dynamic transmitter, Interface Modbus RTU, display, RJ12 connection socket (for X-AIRCONTROL)
Operating mode	Modbus RTU
Volume flow rate	20 – 350 m³/h

Variants

Compact controller XM0-J6 for TVE and TVE-Q

① Compact controller
② Damper blade position indicator and release button
③ Display
④ Rotary selector switch - Selection of options/setting values
⑤ LED button - Selection of menu entry
⑥ Connection socket RJ12

Technical data

Compact controllers for VAV terminal units

Part number	Type of installation component	VAV terminal units
A00000069230	TR0VM-024T-05I-DD15-MB	TVE, TVE-Q

Compact controller TR0VM-024T-05I-DD15-MB with RJ12 connection socket

Type of measurement/installation orientation	Dynamic measurements, any installation orientation
Supply voltage (AC)	24 V AC, ± 20 %, 50/60 Hz
Supply voltage (DC)	24 V DC ± 20 %
Power rating (AC)	NW 100 – 160: maximum 4 VA NW 200 – 400: maximum 7 VA TVE-Q up to height 200: maximum 4 VA TVE-Q from height 300: maximum 7 VA
Power rating (DC)	NW 100 – 160: maximum 2.5 W NW 200 – 400: maximum 4 W TVE-Q up to height 200: maximum 2.5 W TVE-Q from height 300: maximum 4 W
Power consumption (when running/when idle)	1 W
Run time for 90°	100 s
IEC protection class	III (Protective extra-low voltage)
Protection level	IP 42 (with attached terminal cover)
EC conformity	EMC to 2014/30/EU
Bus connection	Modbus RTU, RS485
Number of nodes	128
Adjustable communication parameters	1200 – 115,200 Bd Start bit: 1 Data bits: 8 Stop bits: 1 or 2 Parity: None, Even, Odd
Setpoint / actual value interface (Modbus)	Via X-AIRCONTROL/Modus register list
Cable termination	externally required

Interface configuration of the control component

The communication interface for the control component is pre-set to Modbus at the factory for use with the X-AIRCONTROL zone module. Only the Modbus address must be set by the customer, depending on the use in the supply air and extract air. For other applications, data transmission speed and format must be adapted on site according to the network environment.

XM0–J6	Setpoint value default setting via:	Actual values via:	corresponds to order key option	Menu configuration (Mode)
Analogue operation *	analogue 0 - 10 V	analogue 0 - 10 V	V or F	CA0
Analogue operation *	analogue 2 - 10 V	analogue 2 - 10 V	V or F	CA2
Modbus operation	Modbus register setpoint	Modbus register actual value or analogue 2 - 10 V	M	CB

* It is not possible to use the analogue interface in combination with the RJ12 connection socket provided with the XM0-J6 variant. Therefore, the configuration register 122 (interface mode) must not be changed on site. To use an analogue interface, type XM0 must be installed.

Téléchargements

Information produit

Product data sheet control components XM0-J6

XM0-J6_PD_2024_12_03_DE_en Product data sheet 820 ko pdf

Certificats

Konformitätserklärung / Declaration of conformity TVE - XM0 XS0 XB0 EASY

TVE-XM0XS0XB0EASY_CE_01_2020_07_30--3-_de_en_fr Certificate 190 ko pdf

En cliquant sur ce bouton, vous nous autorisez à vous offrir une expérience de navigation et d'achat de qualité sur notre site web. Ces cookies comprennent ceux qui sont nécessaires au fonctionnement du site et au contrôle de nos services et applications, ainsi que ceux qui sont utilisés uniquement à des fins statistiques, pour des paramètres de commodité ou pour afficher un contenu personnalisé. Vous pouvez décider quelles catégories vous souhaitez autoriser et vous pouvez ajuster les paramètres d'utilisation des données en fonction de vos propres besoinsS. Veuillez noter que, selon les paramètres que vous avez sélectionnés, toutes les fonctionnalités de la page peuvent ne pas être disponibles. Vous pouvez modifier votre sélection à tout moment.

NÉCESSAIRE D’UN POINT DE VUE TECHNIQUE

Ces cookies sont nécessaires au bon fonctionnement de notre site Internet et ne peuvent pas être désactivés. En règle générale, ces cookies ne sont définis qu'en réponse aux actions que vous avez entreprises, comme la définition de vos préférences de confidentialité ou la préparation de votre panier. De plus, des fonctionnalités ou supports liés à la sécurité via un webchat dédié sont intégrés, y compris tous les cookies de session de TROX définis une fois que vous vous êtes connecté en tant que client. Vous pouvez configurer votre navigateur pour bloquer ces cookies ou vous en informer. En conséquence, cependant, certaines zones du site Web peuvent ne pas fonctionner comme prévu.

CONTROL COMPONENT WITH DYNAMIC TRANSDUCER AND MODBUS RTU INTERFACE FOR X-AIRCONTROL

General information

Information technique

Function, Specification text, Order code

Variants

Technical data

Téléchargements

Information produit

Product data sheet control components XM0-J6

Certificats

Konformitätserklärung / Declaration of conformity TVE - XM0 XS0 XB0 EASY

NÉCESSAIRE D’UN POINT DE VUE TECHNIQUE

STATISTIQUES ET ANALYSE DE SITE WEB

COMMODITÉ ET PERSONNALISATION

POUR LA MEILLEURE EXPÉRIENCE TROX POSSIBLE